IRWIN Door Lock Installation Kit for Wooden Doors (3111001), Blue

Works very well I’ve installed two dead bolts with minimal effort. Would recommend to anyone.

I don't know how you couldn't be pleased with this item for the money. I paid 10 or 11 bucks for this with an Irwin incentive discount. Even without that it was well worth the money. I used it right away for three lock sets that were upgrades from the old style. I had pulled the old mortised in lock and glued a block to fill the cavity. I also glued in a small block around where the flange had been. It was a real mess to figure out where to drill and this set did it all. Yeah its plastic and flimsy-its a ten dollar item-but it gets the hole saw started in the right place on each side. Yeah the hole saws are not the best but they are fine if you keep pulling them out and cleaning the teeth. Plus its all figured out. I was very skeptical of the "router bit" you put in your drill but as long as you keep your RPM's up it does the job fine. I haven't even used the hinge jig so that's another project for my ten dollar purchase but the rest I know works and is well worth it. I didn't experience blue rubbing off but my doors needed to be puttied sanded and painted from the old lockset anyway. I have a dozen doors to do-It will make it through them all then thats it-A dollar a door!! A+++++

I have never hung a door before and I hung five slab doors with this jig set. After five doors, the kit was pretty much ready for the trash, but I more than got my money's worth out of it. As with anything else, you will get better with each door you hang. Perhaps a more professional (and costly) kit would keep you from some of the mistakes, but if you are careful, you can hang a door and nobody will be able to tell you're not experienced. I'll do the review on a piece-by-piece basis and try to explain what mistakes you should avoid and why the kit does not prevent your making the mistake. Hopefully armed with this info, you will make fewer mistakes than I did, or at least make different mistakes, Small hole saw: this was the worst part of this kit -- it has metal flashing left over from poor manufacturing that prevented it from being assembled properly. I had to grind out the flashing to get it to fit together at all, but then it wobbled quite noticeably. It turned out not to matter too much as the hole it cut was fairly round. In any case it was invisible, so didn’t matter, and it was never so bad as to damage the door. It was just a bit unpleasant holding the drill that wobbled worse than a Weeble®. Large hole saw: This fit together much better than the small holesaw, but the drill bit was very dull and required a lot of force to get it to operate as a pilot hole. The little bit of wobble did cause the plastic jig to move around, but if you go slow at first, make sure you’re centered and not expecting the plastic guide to do too much for you, you can get a round hole in the right place and straight through. Be careful though. Back the hole saw out several times as it contacts the door to make sure you are still centered and not at an angle. Main hole jig: This is a well thought out, but flimsy guide system. Do not expect it to force your tools to the proper position and angles — its a guide that helps you but does not prevent your tool from cutting in the wrong place. You need to hold the drill steady when using this jig, the jig will not do that for you. The biggest problem I had with with jig/guide was with the latch hole and mortise positioning. On such a small dimension (1.5”) a small misplacement amounts to a large miss. The jig has two plastic spring-loaded guides to align the latch hole in the middle of the edge of the door. These plastic “springs” do not force you into the exact middle of the edge. You can easily be off ~1/16” and that amounts to a large miss from the center. Even if you mark the center to try to minimize this error, its difficult to drive the screws into the edge without the jig getting slightly off. This is where the system needs beefing up more (Irwin, if you’re reading…). For the large hole, it would be nice if the jig were more stout, but small errors in the large hole placement don’t amount to much since the door knob bezel covers it up. Latch mortise template and router bit: This was absolutely the best part of this whole kit. The little router bit worked incredibly well with the latch mortise template, and chiseling out the remainder of the wood from the latch mortise was trivial. I encountered two problems in this area. First, the holes for the template pegs are the same holes left over from the main hole jig when its mounted. This is convenient, but as I mentioned above, it’s all-too-easy to be slightly off in the positioning due to the springy, flimsy nature of the edge positioning. So its all-too-easy to be off in the positioning of the mortise template and its difficult to correct issues since the holes in the wood are so close to where you might want to put new holes (for better alignment). Get yourself some good wood tooth picks and glue, or some small dowel pegs. The other problem with the mortise template is that its easy to flub the bit depth when using a drill as a router. It only happened once, but I flubbed the bit depth and compromised my template. I was able to keep using it, but be sure to always press in on the drill and don’t let it lift out of the template track. Hinge mortise template: The hinge mortise template worked a whole lot better than I thought it would. It definitely takes some skill and I can guarantee you will get better with each hinge you mortise. But you will also make new mistakes on each hinge you mortise. One tip is to make sure you clamp your door to something solid behind the spot where you will be chiseling. Also, cut the outline of your hinge mortise with a box cutter. Finally, be aware that higher-quality solid-core doors will behave very differently than hollow core doors — the wood on the edges of solid core doors is just stronger, I discovered. The wood grain also resists clean cutting and chiseling in the stronger doors. Be patient with the stronger doors — make your outline cuts as good as you can before using the chisels. However… if you are hanging higher quality doors, you should seriously consider a different approach for the hinge mortise. I wish I had a router and router template for the hinge mortise. The chisel approach is just too error prone and labor intensive. I wish Irwin had made a template for the hinge mortise that would allow using the router bit they provided. As mentioned above, the latch mortise router bit and template were absolutely the best part of this kit, it would have been nice if the same (or similar) bit could have been used for the hinge mortise. (I guess the hinge mortise depth is shallower than the latch mortise depth, so it would require a different bit, but I definitely think this would be worth paying for vis-a-vis the 19th century chiseling approach).

I have a 30+ year-old house and we're updating all of the locks and doorknobs. Many of the previous holes are too small for the hardware that we've chosen, and I needed a way to drill them out. If you've ever tried to use a hole saw without a guide bit, it's at best an ugly situation. This tool fit the bill and has been perfect for the job. It's not for professionals, but those kits cost $150 and up. For the price, you get great value. This kit comes with a router bit and template for the door hinges, a template for chiseling out strike plates, and two hole saws (one for the knob, one for the lockset itself on the side of the door) and the guide, which is adjustable to both 2 3/8" and 2 3/4" offsets. It does the job very well. Just remember to drill the knob hole from each side and meet in the center of the door. If you try to drill through and aren't 100% aligned you'll chew up the other side of the guide which is made out of plastic. Not that I did that or anything.

Product is functional but very flimsy. It is clamped into place using the screws but the product does not lay flat easily and, can move a bit. I did a knob and deadbolt on the same door and the holes ended up 1/8" out of alignment. The hole saws are considerably smaller than the guide holes so you need to be very careful on your alignment when starting to drill since the jig has so much play you can end up off center by 1/4 inch very easily. If you are serious about doing this task, get a metal jig with more clamping ability. I would return this but it is used and that would be inappropriate.

Every facet of this tool is completely substandard. I am a retired licensed general contractor (CA lic. #564114 expired) and have installed hundreds of lock sets. The pilot drill bit in the arbor wobbles because the set pin is inadequate. This allows the hole saws to move off center when first making contact with the wood, making a very rough, chewed-up hole on the surface of the wood. It's tough to tell if the hole saws are even sharp because of the very thick layer of paint on the teeth. After 1 use, the teeth appeared dull. The hole saw guide is plastic and useless as a guide; you have to rely on the wobbly pilot drill bit. The guide for mortising the throw plate was plastic and made the cut about 1/16" too wide and a bit too deep. The little mortising drill bit was not very sharp. After 1 aborted try with this POC, I put every piece of it in my recycling.

I don't know if I've ever wrote a good review on a product, usually it's only when I have an issue with an item, but this thing is really amazing. I was able to complete the whole process within a very short period of time with what I'd call professional results. Many of the reviews said there was a "wobble" while they were drilling the holes - there was no wobble, in fact the only way that I could see that it might wobble is if you put the threaded collar on upside down so that it didn't tighten properly - I'm not sure, those claims baffle me as drilling was solid and straightforward. The little "router" bit is a little difficult to use in a regular hand drill but it worked - if I was doing several doors I might load this bit in my dremel tool and use my dremel router base, but it really wasn't worth the time to set it all up. A small, sharp chisel would be handy to complete this part of the process. I gave it 4 stars on sturdiness as it is made of plastic (what else could you expect for this low price?) - I made a slight error and nicked the template with the router bit but it'll still work for many, many more doors. Overall a great value for the money.

I used this tool when installing several dead bolt locks at my home. It should have been made from metal as the plastic it is made from wears. The carbon hole saw blades with arbors are good. The center jig screws into place on the door and aligns perfectly for the backset chosen. The router guide is made from plastic and the router bit chewed it up. I used a wood chisel to cut out the lock face plate instead. I only had four locks to cut so it served my purpose well. The price here was cheaper than the local hardware stores. zoz

I spotted this product on a Youtube video, where it looked really easy to use. Whenever you are drilling a new door to fit handles or locks, the MOST difficult part can be to keep the electric drill level/straight. This is particularly important if you are drilling or cutting holes into a very lightweight door, which is not solid right the way through. This kit helps you keep your drill straight, and includes other useful tools for the job as well! The kit consists of the jig itself, - which fits on the end of the door, to help you drill straight whether you are drilling through the side of the door, or through the end. Also, 2 x carbon steel hole saws, a bolt template, and a router bit. There's also a hinge plate template, to help you mark & chisel out the recesses for the hinges on the edge of your door. We needed to replace 8 x (rather dated) sapele-style doors with 8 x new 4-panel lightweight doors. When we fitted the sapele doors at home some years ago, the fitting was very tricky, especially the knobs & locks, and it took us ages. This kit has changed all that, because it makes the whole job quicker, easier. and the finished job looks very neat & professional. For some strange reason, this product (& similar products) are not available on the UK high street, but are widely available in the United States. That said, this one was actually despatched from Germany & arrived quickly. I've read the other reviews, & was surprised to read about some of the difficulties experienced. I can only say that having previously fit 8 doors WITHOUT this tool, and knowing all the things that can go wrong, this tool kit has made the world of difference. I can honestly say that I've had a 3 separate qualified joiners fit doors for me previously, and the finish on the fitting carried out by all of those the joiners was not even close to the finish which we obtained ourselves using this Irwin kit. As with any DIY job, you have to give a bit of thought to the job first, and allow enough time to do the job properly. It's worth knowing that there is a slightly different kit for use on metal doors. In summary, I consider this an excellent little tool kit, with everything you need to fit door locks, knobs, & handles, and makes the fitting very easy indeed. I would certainly recommend this product without hesitation.

I had four ugly, old doors in my house that I was replacing during my renovations, so I went online and ordered four new doors. I was amazed at how inexpensive they were—until my friend Ralph, a retired handyman who helps me with my renovations, pointed out why. I had ordered doors without the holes already cut for the door knobs and locks! Ralph always seems to have a solution for everything, and he told me I needed the IRWIN Door Lock Installation Kit. I had never even known something like this existed. It was about $25, so I ordered it on a Sunday, and it arrived Tuesday. Ralph came over Tuesday afternoon, used the kit to cut the holes for the door hardware, and we were able to get all four doors installed that afternoon. The kit made the job much easier and saved me from having to return the doors and pay considerably more for doors that already had the holes cut. Once we finished, I gave the kit to Ralph. He’s the handyman, and he’s definitely going to get much more use out of it than I will sitting in my house! For about $25, this little gadget allowed us to properly install the hardware on four doors and saved us the expense and hassle of replacing them. If you’re buying interior doors without pre-cut holes, I definitely recommend having this kit on hand. It worked great for us!

El precio no me gustó ,ya que es una herramienta usada y sin filo en las sierras ,por lo demás está muy bien

Good product and value

It didn't include parts advertised. It was supposed to have an extra jig that wasn't included. I bought the kit for that specifically